1. Improved workability - reduces placing time and compaction problems.
2. Minimizes segregation and bleeding problems by improving cohesion.
3. Increased strength - Provides high early strength for precast concrete with the advantage of higher water reduction in the mix.
4. Improved quality - More dense, close textured concrete with reduced porosity and hence more durable.

Dosage
The optimum dosage is best determined by onsite trials with the concrete mix which enables the effects of workability, strength gain or cement reduction to be measured. Site trials with Cemdisper MP should always be compared with mix containing no admixture. As a guide, the rate of addition is generally in the range of 0.5 - 2L/100kg cement.

Over dosing
An overdose of double the recommended amount of Cemdisper MP, will result in very high workability and some retardation of setting time will occur. However, the ultimate compressive strength will not be achieved.

Setting Time
Although, the setting time is dependant on the dosage of Cemdisper MP, the following factors should be considered at the time of preparing concrete.

• Retardation is increased with lower levels of tri-calcium in the cement.
• Lower temperatures will delay the setting time.
• SRC cement gives higher retardation level than ordinary cement.
• Using more than one type of admixture in the same concrete mix could affect the setting time.
• Retardation level is increased when cement replacement materials are used in the concrete mix.

Cemdisper MP: 20kg and 240kg drums.

All tools and equipment should be washed immediately with fresh water to remove left out slurry completely. And dried slurry can be removed mechanically.

Contact Clov’s Technical support team for more information in the below mentioned address.

Compatibility: Can be used with all types of cements except high alumina cement.

Cemdisper MP is compatible with other types of Clov’s admixtures when added separately to the mix. Site trials should be carried out to optimize dosages. Workability: Can be used to produce flowing concrete that requires no compaction.

Some minor adjustments may be required to produce high workable mix without segregation.

Cohesion: Cohesion is improved due to dispersion of cement particles thus minimizing segregation and improving surface finish. Compressive strength: Early strength is increased up to 20% if water reduction is taken advantage of.

Generally, there is improvement in strength up to 20% depending upon W/C ratio and other mix parameters.

Durability: Reduction in W/C ratio enables increase in density and impermeability, thus enhancing durability of concrete.

Health and Safety
Contact with the skin and eyes should be avoided. Must not be swallowed or inhaled. Wear suitable protective gear, gloves, eye or face protection and dust mask. In case of contact with skin, it should be washed with clean and clear water. In case of eye contact, rinse immediately with water and seek medical advice immediately.

For more details on product safety or application process clarification call our Clov’s Technical Team in below mentioned address.

Fire
Cemdisper MP is non-inflammable.

Shelf Life
The shelf life of Cemdisper MP is 6 months provided it is kept unopened in cool and dry condition.

1. Strength increased density and yield maintained with less cement.
2. High strength without need for additional cement.
3. Breakage reduction.
4. Increase in productivity.
5. Reduction in production cycle.

Dosage
The normal dosage is 0.4L for 100 Kg of cement material. The optimum dosage of Cemdisper CB210 to meet specific requirements should always determined by trails, using the actual materials and conditions that will be experienced in use.

Dispensing
Add the measured quantity of the product ¬with water. Thoroughly stir water and Cemdisper CB210 before using. Use the product in wet mixes for optimum results.

Over dosing
Set retardation occurs if the dosage is double than the normal quantity.

Health and Safety Instruction
Cemdisper CB210 is non toxic. Any splashes or contact with the skin should be washed immediately with clean water. Splashes to the eyes should be washed immediately with clean and clear water and seek medical advise.

Fire
Cemdisper CB210 is non-inflammable.

Shelf Life
The shelf life of Cemdisper CB210 is 12 months provided that the pack is unopened and stored in dry condition and no subjection to extreme temperature.

1. Improved workability - reduces placing time and compaction problems.
2. Minimizes segregation and bleeding problems by improving cohesion.
3. Suitable for high speed drying and immediate traffic
4. Suitable to achieve 7 day compressive strengths in 48 hours.
5. Single colourless liquid shows no change in concrete colour when mixed.

An exclusive site test should be carried out for case by case situation to ensure suitability of the product.

Mix Ratio

SITUATION MIX REQUIREMENTS PER 50 KG

General applications 6.0 – 8.0L of clean, potable water

Mix Process

1. CloAccel 300 must always be pre-diluted before addition to the concrete or sand/cement mortar.
2. Always add the correct dose of CloAccel 300 to the gauging water and avoid using it directly to the dry mix.
3. Always add powder to the liquid vice-versa shall result in clogging.
4. The actual dosage shall vary with the temperature and design mix. However the following guidance shall be followed:

Dosage:

Performance

CloAccel 300 will achieve 7 day compressive strengths in 48 hours

CloAccel 300 when added to the mixtures will reduce the open work times.

Physical Properties

• Appearance - Clear liquid
• Shelf life - 12 Months if stored unopened, stored in cool and dry location.
• Density - 1.32 g/cm3
• pH - 9.1

All measurements are taken at 20ºC and 50% relative humidity. Specifications vary according to site conditions and should be taken as a guide only.

CloAccel 300 contains Calcium Chloride and is not suitable for use in RCC structures.

Test Results

According to ASTM C191, with laboratory test conditions,
Initial set time at 20°C (In Concrete) - 2 hours
Final set time at 20°C (In Concrete) - 4 hours

Over dosing
An overdose of product is not recommended of CloAccel 300, will result in fast setting than usual.

Packaging
CloAccel 300: 20 Litres and 200 Litres drums.

Cleaning
All tools and equipment should be washed immediately with fresh water to remove left out slurry completely. And dried slurry can be removed mechanically.

Contact Clov’s Technical support team for more information in the below mentioned address.

Health and Safety
Contact with the skin and eyes should be avoided. Must not be swallowed or inhaled. Wear suitable protective gear, gloves, eye or face protection and dust mask. In case of contact with skin, it should be washed with clean and clear water. In case of eye contact, rinse immediately with water and seek medical advice immediately.

For more details on product safety or application process clarification call our Clov’s Technical Team in below mentioned address.

Fire
CloAccel 300 is non-inflammable.

Shelf Life
The shelf life of CloAccel 300 is 12 months provided it is kept unopened in cool and dry condition.

1. Improved workability - increases placing time and compaction problems.
2. Minimizes segregation and bleeding problems by improving cohesion.
3. Increased strength - Provides no difference in strength of the concrete.
4. Controlled setting time.
5. No chloride ions present, hence it can used for RCC structures.

• Appearance - Red Coloured liquid
• Shelf life - 12 Months if stored unopened, stored in cool and dry location.
• Density - 1.11 g/cm3
• pH - 9.1

All measurements are taken at 20ºC and 50% relative humidity. Specifications vary according to site conditions and should be taken as a guide only.

An exclusive site test should be carried out for case by case situation to ensure suitability of the product.

Dosage
0.3% – 3.0% by weight of cement (150ml – 1500ml for 50 kg cement bag).

The time of retard shall be directly proportional to the dosage of the admixture. The dosage may vary based on the temperature at site and site conditions.

The dosage of the admixture may also vary by quality of cement, course aggregates and w/c.

The optimum dosage is best determined by onsite trials with the concrete mix which enables the effects of workability, strength gain or cement reduction to be measured. Site trials with CloRetarder should always be compared with mix containing no other admixture. As a guide, the rate of addition is generally based on the retardation required as per site.

Over dosing
An overdose the recommended amount of CloRetarder, will result in very high workability and high retardation of setting time. However, the ultimate compressive strength will not be affected.

Compatability
CloRetarder is readily compatible with all other admixtures and doesn’t effect reinforced steel in the concrete structures.

Packaging
CloRetarder: 20 Liters and 200 Liters drums.

Cleaning
All tools and equipment should be washed immediately with fresh water to remove left out slurry completely. And dried slurry can be removed mechanically.

Contact Clov’s Technical support team for more information in the below mentioned address.

Health and Safety
Contact with the skin and eyes should be avoided. Must not be swallowed or inhaled. Wear suitable protective gear, gloves, eye or face protection and dust mask. In case of contact with skin, it should be washed with clean and clear water. In case of eye contact, rinse immediately with water and seek medical advice immediately.

For more details on product safety or application process clarification call our Clov’s Technical Team in below mentioned address.

Fire
CloRetarder is non-inflammable.

Shelf Life
The shelf life of CloRetarder is 12 months provided it is kept unopened in cool and dry condition.